3mm直插led红光,3mm直插led绿光,3mm直插led蓝光,3mm直插led黄光,3mm直插led黄绿光,3mm直插led橙光,指示灯专用灯珠
- 产品型号：TM-L03W-E
- 应用范围：照明、指示、背光等
- 产品描述：台铭直插式LED,体积小,高亮度,能耗低,应用于照明,背光等领域。
产品介绍
注：亮度、角度、色温、紫光波段均可按客户要求做货。
|
Type 规格/型号 |
Emitting Color 颜色 |
Material 原材料 |
View Angle 发光角度 |
VF(V) 电压 |
IV (MCD) 亮度 |
WL(nm) 波长 |
IF(MA） 电流 |
|||
| Typ | Max | Min | Typ | Min | Max | |||||
|
TM-L03R-E （红光） |
Red | AlGaInP | 30° | 1.8 | 2.4 | 2000 | 4000 | 620 | 630 | 20MA |
|
TM-L03Y-E （黄光） |
Yellow | AlGaInP | 30° | 1.8 | 2.4 | 300 | 600 | 585 | 595 | 20MA |
|
TM-L03O-E （黄绿） |
Yellow Green | AlGaInP | 30° | 1.8 | 2.4 | 50 | 100 | 565 | 575 | 20MA |
|
TM-L03O-E （橙光） |
orange | AlGaInP | 30° | 1.8 | 2.4 | 300 | 600 | 600 | 610 | 20MA |
|
TM-L3CG-E （翠绿） |
Green | InGaN/GaN | 30° | 2.8 | 3.4 | 1200 | 8000 | 520 | 530 | 20MA |
|
TM-L3B-E （蓝光） |
Blue | InGaN/GaN | 30° | 2.8 | 3.4 | 300 | 500 | 460 | 475 | 20MA |
|
TM-L3UV365-E （紫光） |
Purple | InGaN/GaN | 30° | 2.8 | 3.4 | 6 | 8 | 365 | 370 | 20MA |
|
TM-L03UV370-E （紫光） |
Purple | InGaN/GaN | 30° | 2.8 | 3.4 | 10 | 13 | 370 | 375 | 20MA |
|
TM-L3UV380-E （紫光） |
Purple | InGaN/GaN | 30° | 2.8 | 3.4 | 14 | 18 | 380 | 385 | 20MA |
|
TM-L03UV400-E （紫光） |
Purple | InGaN/GaN | 30° | 2.8 | 3.4 | 60 | 70 | 395 | 400 | 20MA |
|
TM-L03UV405-E （紫光） |
Purple | InGaN/GaN | 30° | 2.8 | 3.4 | 70 | 80 | 400 | 405 | 20MA |
|
TM-L03UV410-E （紫光） |
Purple | InGaN/GaN | 30° | 2.8 | 3.4 | 80 | 90 | 405 | 410 | 20MA |
|
TM-L3NB55-E （白光） |
White | InGaN/GaN | 30° | 2.8 | --- | 6000 | --- | 5500 | 6000 | 20MA |
|
TM-L3ZB65-E （白光） |
White | InGaN/GaN | 45° | 2.8 | --- | 6000 | --- | 6500 | 7000 | 20MA |
|
TM-L3LB80-E （白光） |
White | InGaN/GaN | 30° | 2.8 | --- | 6000 | --- | 2500 | 10000 | 20MA |
Supporter shaping：
Shaping of the supporter must be conducted before welding. While shaping, the
bending position of the supporter must at least be located at 3mm from the bottom
of the encapsulating resin. Also, avoid multiple bending on the same position。 Please
choose the
appropriate apparatus to fixate the supporter in order to avoid exerting extra pressure
on resin. Using the jointing section of the pin and resin as fulcrum is strictly
prohibited since the pressure mounted would directly damage the internal 。
illuminating structure and thus cause irreversible defection of the product..Due to the
same reason, the interval between the welding hole on the PCB board should be
strictly matched with the pin interval of the product when assembling the product.
bending position of the supporter must at least be located at 3mm from the bottom
of the encapsulating resin. Also, avoid multiple bending on the same position。 Please
choose the
appropriate apparatus to fixate the supporter in order to avoid exerting extra pressure
on resin. Using the jointing section of the pin and resin as fulcrum is strictly
prohibited since the pressure mounted would directly damage the internal 。
illuminating structure and thus cause irreversible defection of the product..Due to the
same reason, the interval between the welding hole on the PCB board should be
strictly matched with the pin interval of the product when assembling the product.
