润滑脂密封轴承的密封方法是在壳体内预填充适量的泰州INA轴承润滑脂，在填充间隙内提供润滑脂。此外，集中润滑脂供应方法也适用于需要润滑的多中点推力球轴承。润滑脂可长期润滑，不含油脂。该密封装置结构简单，应用广泛。油润滑相对简单。
The sealing method of grease seal bearing is to pre-fill the shell with appropriate amount of Taizhou INA bearing grease and provide grease in the filling gap. In addition, the centralized grease supply method is also applicable to multi point thrust ball bearings requiring lubrication. Grease can be lubricated for a long time without grease. The sealing device has simple structure and wide application. Oil lubrication is relatively simple.
向心推力球轴承的安装与拆卸应根据泰州INA轴承部件的结构、尺寸及匹配特点进行。安装和拆卸压力应直接应用于齿圈表面。由于齿圈在轴承工作面上产生凹痕，影响轴承的正常运行，甚至损坏T型轴承，故不能通过滚动体传递。轴承保持架、密封圈、防尘罩等零件容易变形，不能承受轴承的安装或拆卸压力。轴承的安装方法如下：
Installation and disassembly of centripetal thrust ball bearings should be carried out according to the structure, size and matching characteristics of Taizhou INA bearing components. Installation and dismantling pressure shall be applied directly to the surface of the gear ring. Because the tooth ring produces dents on the working surface of the bearing, which affects the normal operation of the bearing and even damages the T-type bearing, it can not be transmitted through the rolling element. Bearing cage, sealing ring, dust cover and other parts are easily deformed, and can not withstand the installation or disassembly pressure of bearings. The installation methods of bearings are as follows:
1。轴承外圈与壳体孔紧密配合，内圈与轴松配合。轴承可以首先被压入壳体中。管的外径应略小于壳体孔的直径。
1. The outer ring of the bearing is tightly cooperated with the shell hole, and the inner ring is loosely matched with the shaft. The bearing can first be pressed into the housing. The outer diameter of the tube should be slightly smaller than the diameter of the shell hole.
2。泰州INA轴承内圈与轴、外环和壳孔紧密配合。装配套的端面应该做成一个环，不仅可以压.轴承的内圈和外圈，还可以压.轴承的内圈和外圈，这样压力可以传递到内圈和外圈，轴承被压到S.land commu。生产线。这种安装方法特别适用于自动对准的向心球面轴承的安装。
2. Taizhou INA bearing inner ring is closely cooperated with shaft, outer ring and shell hole. The end face of the assembly sleeve should be made into a ring, which can not only press the inner and outer rings of the bearing, but also the inner and outer rings of the bearing, so that the pressure can be transmitted to the inner and outer rings, and the bearing is pressed to S. land commu. Production line. This installation method is especially suitable for the installation of centripetal spherical bearings with automatic alignment.
三。轴承内圈与轴紧配合，外环与壳体松配合。泰州INA轴承可以先用压力机压在轴承上，然后将轴和轴承装入壳体中。当软金属部件（铜或低碳钢）被放置在向心推力球轴承的端面上时，它们被挤压。装配后，套管的内径应略大于轴颈直径，外径应小于轴承内径的挡板直径，以避免对保持架产生压力。当安装大量轴承时，手柄可以连接到衬套上。当向心推力球轴承安装时，轴承孔和轴线的中点线应重合。
Three. The inner ring of the bearing is tightly matched with the shaft, and the outer ring is loosely matched with the shell. The bearing of Taizhou INA can be pressed on the bearing first with a press, and then the shaft and bearing are loaded into the shell. When the soft metal parts (copper or low carbon steel) was placed in the end ball bearing on when they are pressed. After assembly, the inner diameter of the casing should be slightly larger than the Journal diameter, and the outer diameter should be smaller than the baffle diameter of the bearing inner diameter to avoid pressure on the cage. When a large number of bearings are installed, the handle can be connected to the bushing. When the centripetal thrust ball bearing is installed, the midpoint line of the bearing hole and the axis should be coincided.
4。向心推力球轴承的加热、泰州INA轴承安装和安装所需的力与轴承的尺寸和配合干涉的大小有关。对于大、中型轴承大的干扰，常用的热装方法。当热装时，80-100C轴承或可分离轴承环（不超过100C）在油箱或特殊加热器中加热。
4. Heating and centripetal thrust ball bearing Taizhou INA bearing installation and install the required force and the bearing size and the size of interference. For large and medium bearing large interference, commonly used hot charging method. When the hot charging, 80-100C bearings or separable bearing ring (less than 100C) in the heating tank or special heater.
文章来自：泰州SKF轴承 www.wh-skf.com
The article is from: Taizhou SKF bearing www.wh-skf.com
文章来自：泰州INA轴承 www.ina-china.cn
The article is from: Taizhou INA bearing www.ina-china.cn
文章来自：泰州NSK轴承 www.klbbearings.com
The article is from: Taizhou NSK bearing www.klbbearings.com
QQ：524085168
电话：0510-81207777
手机：13311666672
