表面涂有防锈油。清洁的汽油或煤油在安装前必*须仔细清洁，然后涂上清洁的、高质量的或高速的高温润滑脂。泰州SKF轴承清洁度对生活和振动和噪音有很大的影响。但我们要特别提醒您，完全关闭不需要清洁和加油。
The surface is coated with anti-rust oil. Clean gasoline or kerosene must be carefully cleaned before installation and then coated with clean, high-quality or high-speed high-temperature grease. Taizhou SKF bearing cleanliness has a great impact on life and vibration and noise. But we would like to remind you in particular that no cleaning and refueling is required for the complete closure.
润滑对操作和使用寿命有非常重要的影响。简要介绍了油分离的一般原理。润滑脂由基础油、增稠剂和添加剂组成。同类型和牌号的润滑脂性能差别很大。允许旋转限*制是不同的。注意选择是很重要的。泰州SKF轴承润滑脂的性能主要由基础油决定。一般来说，低粘度基础油适用于低温、高速，高粘度基础油适用于高温、高负荷。增稠剂也与润滑性有关。增稠剂的耐水性决定了润滑脂的耐水性。原则上，不同牌子的润滑脂不能混合，甚至同一种增稠剂润滑脂，由于添加剂不同，会对彼此产生负面影响。
Lubrication has a very important effect on operation and service life. The general principle of oil separation is briefly introduced. Lubricating grease consists of base oil, thickener and additive. Greases of the same type and brand have very different properties. The allowable rotation limit * system is different. It's important to pay attention to choices. The performance of Taizhou SKF bearing grease is mainly determined by base oil. Generally speaking, low viscosity base oil is suitable for low temperature and high speed, and high viscosity base oil is suitable for high temperature and high load. Thickeners are also related to lubricity. The water resistance of the thickener determines the water resistance of the grease. In principle, different brands of grease can not be mixed, or even the same thickener grease, because of the different additives, will have a negative impact on each other.
润滑时，泰州SKF轴承润滑油用量越多，效果越好。这是一个普遍的误解。房间里过多的油和油脂会引起油脂的过度搅拌，导致*极高的温度。填充润滑剂的用量应为1/2-1/3，内部空间应填充，高速时应减少到1/3。
When lubricating, the more lubricating oil used in Taizhou SKF bearings, the better the effect. This is a common misunderstanding. Excessive oil and grease in the room can cause excessive stirring of grease, resulting in extremely high temperature. The dosage of filling lubricant should be 1/2-1/3, the inner space should be filled, and it should be reduced to 1/3 at high speed.
安装时，不要直接接触端面和非应力表面。使用压块、套筒或其*他安装工具使力均匀。不要通过滚动元件安装传动力。如果安装表面被润滑，泰州SKF轴承安装将更加平滑。如果干扰严重，应将矿物油加热至80-90℃，并尽快安装。严格控制油温不超过100℃，防止硬度降低和尺寸回火的影响。当拆卸遇到困难时，建议您使用拆卸工具进行拆卸，同时小心地在内环上喷洒热油。热将扩大内环，使其更容易脱落。
When installing, do not directly contact the end face and non-stress surface. Use a press block, sleeve or its * he installs tools to make the force uniform. Do not install transmission force through rolling elements. If the installation surface is lubricated, the installation of Taizhou SKF bearings will be more smooth. If the disturbance is serious, the mineral oil should be heated to 80-90 C and installed as soon as possible. Strict control of oil temperature not exceeding 100 C to prevent the effect of hardness reduction and size tempering. When disassembly encounters difficulties, it is recommended that you use the disassembly tool for disassembly, while carefully spraying hot oil on the inner ring. Heat will expand the inner ring, making it easier to fall off.
文章来自：泰州SKF轴承 www.wh-skf.com
Article from: Taizhou SKF Bearing www.wh-skf.com
文章来自：泰州INA轴承 www.ina-china.cn
Article from: Taizhou INA Bearing www.ina-China.cn
文章来自：泰州NSK轴承 www.klbbearings.com
Article from: Taizhou NSK Bearing www.klbbearings.com
QQ：524085168
电话：0510-81207777
手机：13311666672/13395185757
