成形弹性夹与弹性板的连接利用弹性变形弹性元件的弹性力来实现保持架的紧固，并通过弹性元件与圆柱销的组合来实现连接，这就要求保持架有足够的空间，所以常用于连接大型夹具。T型徐州NSK轴承保持架。
The connection between the forming elastic clamp and the elastic plate uses the elastic force of the elastic deformable element to achieve the fastening of the cage and the combination of the elastic element and the cylindrical pin to achieve the connection, which requires the cage to have enough space, so it is often used to connect large clamps. T-type Xuzhou NSK bearing cage.
1)检查机械密封的类型和规格，以满足设计图纸的要求。所有零件（尤其是密封件和辅助密封件）均未受损、变形和破裂。如果有缺点，**须更换或修理。
1) Check the types and specifications of mechanical seals to meet the requirements of design drawings. All parts (especially seals and auxiliary seals) are undamaged, deformed and cracked. If there are any shortcomings, ** must be replaced or repaired.
2)检查机械密封各部分的尺寸、表面粗糙度和平行度是否满足设计要求。
2) Check whether the dimensions, surface roughness and parallelism of each part of mechanical seal meet the design requirements.
3)使用小弹簧机械密封时，检查徐州NSK轴承长度是否与小弹簧的刚度相同。
3) When using small spring mechanical seal, check whether the length of Xuzhou NSK bearing is the same as the stiffness of small spring.
4)检查主机的位移、摆动和挠度是否满足技术要求，密封室是否满足安装尺寸以及密封盖是否垂直于轴。一般要求是：轴的位移不超过（+0.5mm）；轴的摆动（衰减）不超过0.06mm；轴的**大挠度不超过0.05mm；密封盖和密封垫片之间的接触面不垂直于轴。轴。心线。差值为0.03～0.05mm。
4) Check whether the displacement, swing and deflection of the main engine meet the technical requirements, whether the sealing chamber meets the installation size and whether the sealing cover is perpendicular to the shaft. The General requirements are as follows: the displacement of the shaft does not exceed (+0.5mm); the swing (attenuation) of the shaft does not exceed 0.06mm; the large deflection of the shaft does not exceed 0.05mm; and the contact surface between the sealing cover and the sealing gasket is not perpendicular to the shaft. Shaft. The heart line. The difference is 0.03-0.05 mm.
5)应保持清洁，特别是徐州NSK轴承旋转环、静环密封面和辅助密封环表面应无杂质和灰尘。严禁用脏布擦拭密封面。
5) Should keep clean, especially Xuzhou NSK bearing revolving ring, static ring sealing surface and auxiliary sealing ring surface should be free of impurities and dust. It is strictly forbidden to wipe the sealing surface with dirty cloth.
6)敲击工具，以防止损坏密封元件。
6) Knock tools to prevent damage to sealing elements.
两个线程是用线程固定的。区别在于**一螺杆承受拉应力，而**二螺杆承受压剪应力。
Two threads are fixed by threads. The difference is that ** one screw bears tensile stress while ** two screw bears compressive shear stress.
更换轴承时，不必在设备附近拆卸轴承，缩短了轴承总安装时间，降低了工作要求，大大缩短了主机停机时间，提高了徐州NSK轴承生产效率。基于上述优点，分体轴承的应用越来越广泛。
When replacing bearings, it is not necessary to disassemble bearings near the equipment, which shortens the total installation time of bearings, reduces the working requirements, greatly shortens the downtime of the main engine, and improves the production efficiency of NSK bearings in Xuzhou. based on the above advantages, split bearing is more and more widely used.
结论：
Conclusion:
单个的轴承保持架通常是两个半结构，安装后组装和连接。对于笼子的尺寸和空间有一定的要求。不同的连接方式会影响轴承的尺寸和数量，进而影响轴承的性能。
A single bearing cage is usually two and a half structures, assembled and connected after installation. There are certain requirements for the size and space of the cage. Different connection modes will affect the size and number of bearings, and then affect the performance of bearings.
文章来自：徐州SKF轴承 www.wh-skf.com
Article from: Xuzhou SKF Bearing www.wh-skf.com
文章来自：徐州INA轴承 www.ina-china.cn
Article from: Xuzhou INA Bearing www.ina-China.cn
文章来自：徐州NSK轴承 www.klbbearings.com
Article from: Xuzhou NSK Bearing www.klbbearings.com
QQ：524085168
电话：0510-81207777
手机：13311666672/13395185757
