为了使进口徐州INA轴承的原始性能尽可能保持良好，有必要对其进行维护、修理和预防事故的发生，保证运行的可靠性，提高生产和经济性。应根据相应机械操作条件的操作标准定期进行维护。其内容包括监测运行状态、补充或更换润滑油功能：检查可减少或避免摩擦磨损、定期解体。进口轴承作为运行中的一个维护项目，具有旋转噪声、振动、温度和润滑等特点。
In order to maintain the original performance of imported Xuzhou INA bearings as good as possible, it is necessary to maintain, repair and prevent accidents, ensure the reliability of operation and improve production and economy. Maintenance should be carried out regularly according to the operating standards of the corresponding mechanical operating conditions. Its contents include monitoring operation status, supplementing or replacing lubricating oil function: inspection can reduce or avoid friction and wear, periodic disintegration. As a maintenance project in operation, imported bearings have the characteristics of rotating noise, vibration, temperature and lubrication.
进口轴承清洗：在拆卸和修理进口徐州INA轴承时，应首先记录进口轴承的外观，确认润滑油的残留量，并在清洗轴承前对润滑油进行取样和检查。汽油和煤油是常用的清洁剂。
imported bearing cleaning: When disassembling and repairing the imported Xuzhou INA bearing, the appearance of the imported bearing should be recorded first, the residual amount of lubricant should be /confirm/ied, and the lubricant should be sampled and inspected before cleaning the bearing. Gasoline and kerosene are commonly used detergents.
去除进口轴承的清洗、粗清洗和精清洗，分别放在容器内，首先放在金属网底部，使进口轴承不直接接触容器污垢。在大多数情况下，轴承疲劳损伤会导致轴承疲劳损伤。
Remove the cleaning, rough cleaning and fine cleaning of imported bearings, respectively, in the container, first placed at the bottom of the metal mesh, so that the imported bearings do not directly contact the containers dirt. In most cases, bearing fatigue damage will lead to bearing fatigue damage.
一般来说，徐州INA轴承疲劳损伤造成的损伤只有三分之一来自润滑不顺，三分之一来自污染物进入轴承或安装和处理不当。然而，这些类型的损坏都是与工业轴承无关的精要零件，所以在使用高性能轴承时要小心，即使使用不当，也不能达到预期的性能效果，而且容易造成轴承损坏。粗清洗时，如果进口轴承有污物旋转，会损坏进口轴承的滚动面。我们应该注意它。在原油清洗油中，油和粘合剂用刷子除去，粗洗，然后用擦洗代替。
Generally speaking, only one third of the fatigue damage of Xuzhou INA bearing comes from lubrication failure, and one third comes from pollutants entering the bearing or improper installation and treatment. However, these types of damage are not related to industrial bearings, so be careful when using high-performance bearings, even if improper use, can not achieve the desired performance results, and easy to cause bearing damage. When rough cleaning, if the imported bearing rotates with dirt, the rolling surface of the imported bearing will be damaged. We should pay attention to it. In crude oil cleaning oil, oil and adhesives are removed by brush, roughly washed, and then replaced by scrubbing.
清洗徐州INA轴承是将进口轴承在清洗油中旋转，同时仔细清洗。此外，清洁的油也应定期保持清洁。
Cleaning Xuzhou INA bearing is to rotate the imported bearing in the cleaning oil, while carefully cleaning. In addition, clean oil should also be kept clean regularly.
进口轴承的检查和判断：为了判断拆下的进口轴承是否可以使用，进口轴承务必在清洗后进行检查。检查滚道表面、滚动面和配合面状态，保持架磨损件的基本失效类型，进口轴承间隙增大和尺寸精度降低造成的损坏和异常。然后用一只手将不可分离的小滚珠轴承支撑在内环的水平面上，转动外环以确认其光滑度。
Inspection and judgment of imported bearings: In order to judge whether the imported bearings removed can be used, imported bearings must be inspected after cleaning. Check the state of raceway surface, rolling surface and mating surface, the basic failure type of cage wear parts, the damage and abnormality caused by the increase of inlet bearing clearance and the decrease of dimension accuracy. Then the inseparable small ball bearing is supported on the horizontal surface of the inner ring with one hand, and the outer ring is rotated to confirm its smoothness.
圆锥滚子轴承和其余单独徐州INA轴承可分别用于检查滚动体和外圈的滚道表面。
Tapered roller bearings and other individually Xuzhou INA bearings can be used to inspect the raceway surfaces of rolling bodies and outer rings respectively.
由于大型进口轴承不能用手转动，应注意滚子、滚道表面、保持架和保持架的外观。进口轴承越重要，检查就越仔细。
Since large imported bearings cannot be rotated by hand, attention should be paid to the appearance of rollers, raceway surfaces, cages and cages. The more important the imported bearing is, the more careful the inspection will be.
文章来自：徐州SKF轴承 www.wh-skf.com
Article from: Xuzhou SKF Bearing www.wh-skf.com
文章来自：徐州INA轴承 www.ina-china.cn
Article from: Xuzhou INA Bearing www.ina-China.cn
文章来自：徐州NSK轴承 www.klbbearings.com
Article from: Xuzhou NSK Bearing www.klbbearings.com
QQ：524085168
电话：0510-81207777
手机：13311666672/13395185757
